Search found 16 matches

by HondaLee
Tue Feb 12, 2019 12:47 pm
Forum: OutBack
Topic: Flex ware 250
Replies: 8
Views: 3722

Re: Flex ware 250

IÔÇÖm guessing maybe an older version?
by HondaLee
Tue Feb 12, 2019 12:46 pm
Forum: OutBack
Topic: Flex ware 250
Replies: 8
Views: 3722

Re: Flex ware 250

Thanks for the information but my mate didnÔÇÖt have a page 4. Any ideas why?
by HondaLee
Sat Feb 09, 2019 6:23 am
Forum: OutBack
Topic: Flex ware 250
Replies: 8
Views: 3722

Re: Flex ware 250

From the advanced screen I found nothing that says grid-tied. Only grid,gen,use or drop.
Cane you give further instructions.
by HondaLee
Fri Feb 08, 2019 1:07 pm
Forum: OutBack
Topic: Flex ware 250
Replies: 8
Views: 3722

Re: Flex ware 250

Question 2: can you explain the function ( inverter control ) and the difference in Srch,on,off
Thanks
by HondaLee
Fri Feb 08, 2019 1:04 pm
Forum: OutBack
Topic: Flex ware 250
Replies: 8
Views: 3722

Re: Flex ware 250

Question: I have a flex ware 250 with GVFX 3648
Can I control the gridtied function from the mate or dose it require a mate3?
by HondaLee
Thu Feb 07, 2019 1:27 pm
Forum: OutBack
Topic: Flex ware 250
Replies: 8
Views: 3722

Flex ware 250

I have a flex ware 250 just installed and the LCD screens on the mate and charge controller are not readable. I believe this is from sitting in direct sunlight for a couple years while not installed. I need information on getting LCD screens repaired or replaced. Thanks
by HondaLee
Fri Jan 04, 2019 5:59 pm
Forum: Grid Tie Applications
Topic: Flex ware 250 GVFX 3648 Question
Replies: 4
Views: 3216

Re: Flex ware 250 GVFX 3648 Question

Hi, The GVFX will offset your loads connected to the AC output of the inverter, if renewable power is still available it will send the reminder to the AC input feeding your Main panel. Here is a quick video describing how the power flow works: https://youtu.be/ssMhDa6tdu4 -Jorge Question: if I wire...
by HondaLee
Fri Jan 04, 2019 1:49 pm
Forum: Grid Tie Applications
Topic: Flex ware 250 GVFX 3648 Question
Replies: 4
Views: 3216

Flex ware 250 GVFX 3648 Question

I have a wiring question on the flex ware 250 with the GVFX3648 inverter. Diagram shows (power in )coming from grid then shows power out going to load panel my question is how dose it feed back to grid? IÔÇÖm getting my grid power for (power in)from my main house breaker panel All of my loads are on...
by HondaLee
Tue Dec 18, 2018 4:08 pm
Forum: FLEXmax Charge Controllers
Topic: FLEXmax 80 display
Replies: 7
Views: 4080

Re: FLEXmax 80 display

Yes I did rewire solar array so now wired in strings of 3.
by HondaLee
Mon Dec 17, 2018 7:55 am
Forum: FLEXware
Topic: Advice on best way to setup my outback system
Replies: 5
Views: 21258

Re: Advice on best way to setup my outback system

The FLEXmax 250 has its own mate3 and hub.
You think there should be any issue with long term with excess voltage to charge controller?
From what I have read the one 36.6 volt panel in each string should have reduced the 37.5 panels if anything.if it did go over it had to be very little over.
by HondaLee
Sun Dec 16, 2018 8:55 am
Forum: FLEXware
Topic: Advice on best way to setup my outback system
Replies: 5
Views: 21258

Re: Advice on best way to setup my outback system

Thanks mike for responding to my question. I was following you till you were talking about generator to aux panel. What I have done at present is pretty much what you described except I just disconnected circuits from main home breaker panel and wired them to outback ac panel breakers. The problem w...
by HondaLee
Sat Dec 15, 2018 10:53 am
Forum: FLEXmax Charge Controllers
Topic: FLEXmax 80 display
Replies: 7
Views: 4080

Re: FLEXmax 80 display

Did hard reset on charge controller and it made no difference. Every single caricature has Black box in place of letter over hole screen.
What next?
by HondaLee
Sat Dec 15, 2018 9:28 am
Forum: FLEXware
Topic: Advice on best way to setup my outback system
Replies: 5
Views: 21258

Advice on best way to setup my outback system

Thank you in advance for sharing your knowledge! I will start by telling you what outback equipment I own FLEXmax 500 with model VFX3648 inverters FLEXmax 250 with model GVFX3648 Inverter Two FLEXmax 80 charge controllers 48vdc 500 amp hour agm battery bank One solar array with 3500 watts with plans...
by HondaLee
Sat Dec 15, 2018 8:54 am
Forum: FLEXmax Charge Controllers
Topic: FLEXmax 80 display
Replies: 7
Views: 4080

Re: FLEXmax 80 display

Clipper creek model LCS-20P
Configuration LCP-20-C11-P1-L25-55
No I havenÔÇÖt tried any other loads yet as I am just getting the system installed but I did check voltage and was getting a little better than 220 vac
by HondaLee
Thu Dec 13, 2018 5:37 pm
Forum: FLEXmax Charge Controllers
Topic: FLEXmax 80 display
Replies: 7
Views: 4080

Re: FLEXmax 80 display

I will try that and get back to you. I have another question: I have a second FLEXmax 80 that I used to change out the one that is giving problems. With replacement charge controller installed and system up and running I am getting 227vac. I plugged in my cripplecreek car charger and it immediately ...
by HondaLee
Thu Dec 13, 2018 10:29 am
Forum: FLEXmax Charge Controllers
Topic: FLEXmax 80 display
Replies: 7
Views: 4080

FLEXmax 80 display

After moving to my current location I installed my system and when I turned on dc breakers FLEXmax 80 display has back light and a full screen of black boxes and no letters. The rest of system seems ok so far , can you help